Published 2026-11-19 · Cyclone Bolt
Flange bolts are the stud bolts and heavy hex nuts that clamp two pipe flanges together over a gasket. For a standard ASME B16.5 flange, the number of studs, their diameter and their length all follow from the nominal pipe size and the pressure class, and the stud and nut grades come from the piping specification. This article explains how those details are set and how they become an order for stud bolts and nuts.
What are flange bolts?
In pipe flange work, the "bolt" is normally a stud bolt: a rod threaded end to end, with no head, tightened with a heavy hex nut on each end. It is the standard fastener for bolted pipe flanges, valves and pressure vessels. The heavy hex nut that goes with it is wider across the flats and thicker than a standard hex nut of the same thread size, with inch dimensions set by ASME B18.2.2. A stud and two nuts make one bolt position; a flange needs as many sets as it has bolt holes.
The flange itself comes from ASME B16.5, Pipe Flanges and Flanged Fittings. ASME says the standard covers pressure-temperature ratings, materials, dimensions, tolerances, marking, testing and methods of designating openings for flanges with rating class designations 150, 300, 400, 600, 900 and 1500 in sizes NPS 1/2 through NPS 24, and Class 2500 flanges in sizes NPS 1/2 through NPS 12. ASME also states that the standard includes requirements and recommendations regarding flange bolting, flange gaskets and flange joints. The edition listed on ASME's page is B16.5-2025, and ASME notes the standard has been placed on stabilized maintenance.
How many flange bolts does a flange take?
The bolt count and diameter are fixed by B16.5 for each pipe size and class. The contents of the B16.5-2020 edition, which ASME issued on January 29, 2021, list a table of flange bolting dimensional recommendations and a list of applicable ASTM bolting specifications. Cyclone's published flange bolt chart tabulates the stud count and diameter for Class 150, 300, 600 and 900 flanges from NPS 1 through NPS 24. A few rows show the pattern: the count rises with pipe size, and the diameter rises with pressure class.
| NPS | Class 150 | Class 300 | Class 600 | Class 900 |
|---|---|---|---|---|
| 2 | 4 studs, 5/8 in. | 8 studs, 5/8 in. | 8 studs, 5/8 in. | 8 studs, 7/8 in. |
| 4 | 8 studs, 5/8 in. | 8 studs, 3/4 in. | 8 studs, 7/8 in. | 8 studs, 1-1/8 in. |
| 6 | 8 studs, 3/4 in. | 12 studs, 3/4 in. | 12 studs, 1 in. | 12 studs, 1-1/8 in. |
| 8 | 8 studs, 3/4 in. | 12 studs, 7/8 in. | 12 studs, 1-1/8 in. | 12 studs, 1-3/8 in. |
| 12 | 12 studs, 7/8 in. | 16 studs, 1-1/8 in. | 20 studs, 1-1/4 in. | 20 studs, 1-3/8 in. |
| 24 | 20 studs, 1-1/4 in. | 24 studs, 1-1/2 in. | 24 studs, 1-7/8 in. | 20 studs, 2-1/2 in. |
The full chart carries every size from NPS 1 through 24 in each class, with lengths. Class 1500, Class 2500 and ASME B16.47 flanges are outside that chart and are quoted on request.
Flange bolt length: raised face vs. ring joint
Length is where orders go wrong. The facing matters as much as the size: on Cyclone's chart a raised face or flat face joint takes a shorter stud than a ring-type joint of the same size and class. For example, an NPS 6 Class 300 flange takes twelve 3/4 in. studs, 4-3/4 in. long for a raised or flat face and 5-1/2 in. long for a ring joint. B16.5 itself carries an annex with a method for calculating bolt lengths, with separate entries for machine bolt length and stud bolt length.
Chart lengths are measured first thread to first thread, without the points. Drawings do not all use that convention, so the order states which one applies. Cyclone's chart also asks buyers to verify coating build-up and service conditions, since either can change the length that fits.
Thread series for flange studs
A stud size is written as diameter, then threads per inch, so 3/4-10 is a 3/4 in. stud with 10 threads per inch. Cyclone's chart gives the usual practice for flange and pressure service: coarse (UNC) threads through 1 in., and 8 threads per inch (8UN) above 1 in. A nut tapped for one series does not fit a stud cut in the other, so the order carries the series and the thread class.
Stud and nut grades for flange bolts
The grade of the flange bolts comes from the piping specification and the service, not from the flange standard alone. For alloy and stainless studs in pressure and high-temperature service, the usual specification is ASTM A193, and the matching nuts come from ASTM A194. ASTM's description of A194 says the nuts are intended for high-pressure or high-temperature service or both, puts carbon, alloy and martensitic stainless nuts in the size range 1/4 through 4 in. and metric M6 through M100, and states that grade substitutions without the purchaser's permission are not allowed. ASTM's store lists A194/A194M-26 as the active edition.
Each A193 stud grade has a conventional A194 nut. The pairings below are the ones published on Cyclone's heavy hex nut page and ASTM A193 guide; the assembly specification on the order governs.
| A193 stud grade | Material | Usual A194 nut |
|---|---|---|
| B7 | Chromium-molybdenum alloy steel, quenched and tempered | 2H |
| B7M | Chromium-molybdenum alloy steel, hardness limited | 2HM |
| B16 | Chromium-molybdenum-vanadium alloy steel | 4 or 7 |
| B8 | Type 304 stainless steel | 8 |
| B8M | Type 316 stainless steel | 8M |
The most widely specified set, according to Cyclone's stud bolt page, is an A193 B7 stud with two A194 2H heavy hex nuts, listed in plain, TFE blue and cadmium-plated finishes. Which grade, class and finish apply to a given line comes from the customer's engineer and the governing code.
Assembly guidance: ASME PCC-1
How the joint is put together is a separate document. ASME PCC-1, Pressure Boundary Bolted Flange Joint Assembly, is listed by the standards distributor Nimonik as the current revision, issued October 2026. Its description says the guidelines apply to pressure-boundary flanged joints with ring-type gaskets and are intended for assemblers, designers, supervisors, inspectors and instructors in all industries that employ such joints. The listing names appendices on training and qualification of bolted joint assemblers, on alternative flange bolt assembly patterns, and on troubleshooting joints that do not give leak-tight performance. Assembly procedure and bolt load are set by the owner's engineering, not by the stud supplier.
What goes on a flange bolt order
Buyers typically list the stud specification and grade (for example ASTM A193 B7), the nut specification and grade (ASTM A194 2H), nominal diameter, thread series and class, stud length and the length convention, the number of studs and the number of nuts per stud, the finish on each, the quantity of sets, and the documentation required, usually material test reports and a certificate of conformance. Giving the flange class, pipe size and facing lets the supplier check the count, diameter and length against the chart before cutting.
Where Cyclone fits
Cyclone Bolt is a Houston, Texas manufacturer of fasteners, threaded products and custom machined components, established in 2016. Cyclone manufactures stud bolts in diameters from 1/4 in. through 4 in., cut to the length on the order, and supplies A194 heavy hex nuts from 5/8 in. through 4 in., with A193 B7 studs and A194 2H nuts listed in plain, TFE blue and cadmium-plated finishes. The company holds AS9100D, AS9120B, ISO 9001:2015, API Spec Q1, API 20E and API 20F certifications, listed on its quality page.
For flange stud sets cut to your pipe size, class and facing, with the grade, thread and documentation your order requires, request a quote.
Sources
- B16.5 - Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24, Metric/Inch Standard, ASME, 2026-11-19
- ASME B16.5-2020, Pipe Flanges and Flanged Fittings (front matter and contents), ASME, 2021-01-29
- A194/A194M Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-Temperature Service, or Both, ASTM International, 2017-08-16
- ASME PCC-1-2026 - Pressure Boundary Bolted Flange Joint Assembly, Nimonik, 2026-11-19