Published 2026-11-17 · Cyclone Bolt
B7 threaded rod is alloy steel bar threaded along its full length and made to ASTM A193 Grade B7, the chromium-molybdenum bolting grade that is quenched and tempered to a minimum tensile strength of 125,000 psi in diameters through 2-1/2 inches. It is the raw stock that A193 B7 stud bolts are cut from, and it is bought for flange, valve and pressure-vessel bolting where ordinary all-thread has no place. The difference is not the shape; it is the specification behind the steel.
What is B7 threaded rod?
The grade comes from ASTM A193/A193M, the Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications. ASTM says the specification covers alloy steel and stainless steel bolting material for pressure vessels, valves, flanges and fittings, and that ferritic steels under it are to be heat treated to suit the high-temperature characteristics of each grade. The current edition is A193/A193M-26.
Within that specification, B7 is the chromium-molybdenum alloy steel grade. Cyclone's ASTM A193 bolting guide lists its usual base steels as AISI 4140, 4142 and 4145, quenched and tempered. "Threaded rod" simply means that bar has been threaded end to end without a head, so any length can be cut from it. When the bar is B7, the result is B7 threaded rod: a product form (rod) carrying a material grade (A193 B7).
B7 threaded rod vs. ordinary all-thread
"All-thread" names a shape, not a grade. A rod sold only as all-thread, with no specification on the tag, carries no promise about chemistry, heat treatment or tested strength. A rod sold as A193 B7 carries all three. ASTM's scope for A193 states that bars and wire under the specification are hot-wrought and may be further processed by centerless grinding or cold drawing, that chemical composition requirements are set for each alloy, and that tensile and hardness requirements apply, with the tensile requirement demonstrated by wedge tensile testing of full-size fasteners.
For a buyer, that translates into paperwork. B7 rod is bought against a heat number and a material test report showing the chemistry and the mechanical test results. A rod sold only as all-thread carries no such requirement, which is why the two are not interchangeable on a pressure flange even when they look alike on the shelf.
ASTM also points buyers to neighboring specifications when B7 is not the right grade: A193 notes that alloy-steel bolting for the lower range of high-temperature applications is covered by ASTM A354, and that alloy-steel bolting for low-temperature applications is covered by ASTM A320/A320M. Which grade applies comes from the customer's engineer and the governing code, not from the rod supplier.
Thread series and sizes for B7 rod
Dimensions for inch threaded rod come from ASME B18.31.3, Threaded Rods (Inch Series), which ASME lists as B18.31.3-2014 (R2025). ASME says the standard covers the general and dimensional data for inch series threaded rods and lists four thread configurations with their diameter ranges. ASME also notes that there are no ISO standards for inch threaded rods, and that a size appearing in the standard does not mean every supplier stocks it.
| Thread series in ASME B18.31.3 | Diameter range |
|---|---|
| UNC (coarse) | #4 through 4 in. |
| UNF (fine) | #4 through 1-1/2 in. |
| 8 UN (8 threads per inch) | 1-1/8 through 4 in. |
| Acme | 1/4 through 5 in. |
The thread form itself is governed by ASME B1.1, Unified Inch Screw Threads. According to ANSI's summary of the 2024 edition, B1.1 applies to the thread form, series, class, allowance, tolerance and designation of unified screw threads, and establishes tolerance classes such as Class 1, 2 and 3 that set how tightly mating threads fit. ANSI dates the Unified Thread Series to 1949, created after World War II when the United States, Great Britain and Canada each still ran their own thread systems.
For B7 flange bolting, Cyclone's A193 guide gives the usual practice: coarse (UNC) threads through 1 inch, and 8 threads per inch (8UN) above 1 inch, unless the order says otherwise. A nut tapped for one series does not fit a rod threaded in the other, which is why the order states the series and the class and the supplier confirms both before cutting.
B7 strength by diameter
A193 steps the minimum mechanical properties of B7 down as the bar gets thicker. The values below are the minimums published on Cyclone's A193 guide and B7 product page; the current edition of the standard and the specification on the order govern.
| A193 B7 diameter | Tensile, min | Yield, min | Usual A194 nut |
|---|---|---|---|
| Through 2-1/2 in. | 125 ksi | 105 ksi | 2H |
| Over 2-1/2 to 4 in. | 115 ksi | 95 ksi | 2H |
| Over 4 to 7 in. | 100 ksi | 75 ksi | 2H |
Two related grades share the family. B7M is B7 with hardness limited to 235 HBW and a 100 ksi minimum tensile strength through 4 inches, paired with A194 2HM nuts. B16 adds vanadium to the chromium-molybdenum chemistry for higher service temperatures. Both are detailed on the A193 guide linked above.
How studs are cut from B7 rod
A B7 stud bolt is a length of B7 rod cut to size with both ends finished, usually with a chamfer or point so the nut starts cleanly. Because the bar is heat treated and tested to A193 as material, cutting a stud to length does not change the grade, and the stud is documented against the heat of rod it came from. That is what lets a manufacturer turn one certified bar into flange studs of many different lengths.
Length is the detail that trips up orders. Cyclone's B7 product page notes that flange stud length is conventionally measured first thread to first thread, without the points, and asks buyers to say which convention their drawing uses. Stud counts, diameters and lengths for standard flange sizes and pressure classes are tabulated in the flange bolt chart. The same rod also yields double-end and tap-end studs when the order calls for a shorter thread on one end.
Which nuts go with B7?
A193 covers nuts for use with its bolting in Section 13 of the specification, and the conventional pairing for B7 is an ASTM A194 Grade 2H heavy hex nut. When the stud is coated, the nut finish is listed with it on the order. The nut grade, like the stud grade, is set by the customer's engineer and the governing code.
What goes on a B7 rod or stud order
Buyers typically list the specification and grade (ASTM A193 B7), nominal diameter, thread series and class, overall length or length convention, quantity, finish, the nut grade when nuts are included, and the documentation required, usually material test reports and a certificate of conformance. Supplementary requirements in A193 apply only when the purchase order calls for them, so an order that needs one, such as additional testing, says so in writing.
Where Cyclone fits
Cyclone Bolt is a Houston, Texas manufacturer of fasteners, threaded products and custom machined components, established in 2016. Cyclone machines stud bolts, including A193 B7 studs with A194 2H heavy hex nuts, in diameters from 1/4 inch through 4 inches, in plain and coated finishes. The company holds AS9100D, AS9120B, ISO 9001:2015, API Spec Q1, API 20E and API 20F certifications, listed on its quality page, and supplies DFARS-compliant material.
For B7 studs cut to your flange schedule, with the thread series, length convention and documentation your order requires, request a quote.
Sources
- A193/A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications, ASTM International, 2026-03-03
- B18.31.3 - Threaded Rods (Inch Series), ASME, 2026-11-17
- ASME B1.1-2024: Unified Inch Screw Threads, The ANSI Blog, 2026-11-17